Current Sensing Probes

CSP 9160
The CSP 9160 is a broadband RF current sensor probe as defined in CISPR 16-1-2. Beside the compliance measurements of asymmetrical disturbance currents as e.g. required in CISPR 16-2-1 and CISPR 22, the probe can be used in a number of diagnostic applications to measure superimposed RF currents flowing in conductors, or cable harnesses.

 

MD 4070
The monitoring device MD 4070 can be used as an active or passive current sensor probe to measure the current in a conductor without connecting it directly. 

CSP 9160

EMC Emission/Immunity Sensing Probe

  • As defined in CISPR 16-1-2

  • Suitable for emission measurements per CISPR 16-2-1, CISPR 22 and CISPR 32

  • Suitable for BCI testing per MIL STD-461 and various automotive standards

  • Flat frequency response 

  • Ruggedly designed 

Description

The CSP 9160 is a broadband RF current sensor probe as defined in CISPR 16-1-2. Beside the compliance measurements of asymmetrical disturbance currents as e.g. required in CISPR 16-2-1 and CISPR 22, the probe can be used in a number of diagnostic applications to measure superimposed RF currents flowing in conductors, or cable harnesses.
A convenient feature of the CSP 9160 is that, from 100 kHz to 120 MHz, it has a flat frequency response with a 0 dB transducer factor, allowing voltage measurements to be read as current, directly without any correction. The probe can be easily and quickly clipped around the cable under test and the RF currents measured using an oscilloscope, spectrum analyzer, or EMI receiver. Its large aperture (25.4 mm) can accommodate most cables and can handle power lines with currents up to 50 amps.  

MD 4070

Monitoring Device 10 kHz to 400 (600) MHz

  • As required in IEC/EN 61000-4-6

  • Suitable for BCI testing per ISO 11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards

  • Active/passive operation for wide dynamic range

  • Suitable for NSG 4070

  • Ruggedly designed

Description

The monitoring device MD 4070 can be used as an active or passive current sensor probe to measure the current in a conductor without connecting it directly. The MD 4070 allows fast and easy measurement as it can be quickly clamped around the current carrying conductor.

The MD 4070 is characterized over the frequency range from 10 kHz to 400 (600) MHz. The MD 4070 can be used for the procedure for clamp injection when the common-mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MD 4070 can also be used as current monitor for BCI testing as per ISO 11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.

Product Suggestions
Screen Shot 2556-06-02 at 8.52.18 PM.png

NSG 3060

Multifunction Generator Systems - The Modular Solution for 6 kV Applications

  • Modular, expandable system

  • Surge, EFT/Burst, Power Quality, Ring Wave, and more

  • Surge voltage up to 6.6 kV for overtesting

  • ANSI and IEC coupling methods

  • Intuitive 7.2” color touch screen interface

  • Expert mode for changing parameters while test is running (diagnostics) 

  • Status LEDs

  • Safety connectors

Screen Shot 2556-06-02 at 8.53.39 PM.png

NSG 1007

Programmable AC and DC Power Sources

  • Combination AC and DC power source and power analyzer 

  • Arbitrary waveform generation

  • Built-in digital power analyzer

  • Meets source requirements for IEC 61000-3-2 and -3-3

  • 3 - 15 kVA for single and three phase applications (15 kVA per phase)

Screen Shot 2556-06-02 at 11.17.42 PM.pn

Near Field Probes

A diagnostic “tool kit” for use in both electrical and mechanical environments featuring three hand held probes (two magnetic, one electric) covering the frequency range 9 kHz to 1 GHz together with a 30 dB pre-amplifier, power adaptor and check jig.

Address

PNK Engineering and Consultant Co., Ltd. 
222 UPA Place Building B  1st Floor
Soi Ramkumhange 164 Minburee 
Bangkok 10510

Contact

Tel +669 4412 5588   +66 2 170 9244
Fax +66 2 170 9245 

©2018 by PNK Engineering & Consultant create by Big Bear